|
|
Seagate ST336706LC SCSI Hard Drive
Item Number: SGT-ST336706LC-RF-OE
Manufacturer's Part Number: ST336706LC |
  |
| |
Seagate Cheetah 36ES 36GB 10K U160 80pin SCA-2 SCSI Hard Drive ST336706LC - Refurbished
|
| |
 |
 |
Capacity: 36GB
Spindle Speed: 10,000RPM
Interface Type: SCSI 80pin SCA-2 (Hot-Swap)
Disk Size: 3.5"x1.0" (Low Profile Hard Drive)
Sustained Throughput (MBps): 52 to 68
Average Seek Time (read/write ms): 2.99
Electrical Interface Speed: SCSI LVD U160 - 160MBps 16-bit
On-Board Cache: 4MB |
| |
 |
 |
These drives will fit in any of our SCSI hard drive trays: |
| |
| |
| |
|
|
|
|
| |
 |
 |
Cheetah 36ES drives combine giant magnetoresistive (GMR) heads, partial response/maximum likelihood (PRML) read channel electronics, embedded servo technology, and a wide SCSI Ultra160 interface to provide high performance, high capacity data storage for a variety of systems including engineering workstations, network servers, mainframes, and supercomputers.
The Cheetah 36ES family has the following standard features: • Integrated Ultra160 SCSI controller • Multimode SCSI drivers and receivers—single-ended (SE) and low voltage differential (LVD) • 16 bit I/O data bus • Asynchronous and synchronous data transfer protocol • Firmware downloadable via SCSI interface • Selectable even byte sector sizes from 512 to 4,096 bytes/sector • Programmable sector reallocation scheme • Flawed sector reallocation at format time • Programmable auto write and read reallocation • Reallocation of defects on command (post format) • Enhanced ECC maximum burst correction length of 240 bits with a guaranteed burst correction length of 233 bits • Sealed head and disc assembly • No preventative maintenance or adjustment required • Dedicated head landing zone • Embedded servo design • Self diagnostics performed when power is applied to the drive • 1:1 Interleave • Zoned bit recording (ZBR) • Vertical, horizontal, or top down mounting • Dynamic spindle brake • 4,096 kbyte data buffer • Hot plug compatibility (Section 9.6.4.2 lists proper host connector needed) for LC model drives • Drive Self Test (DST)
Compatibility
|
| |
 |
 |
ST-336706LW UNFORMATTED CAPACITY (GB) ________________ FORMATTED CAPACITY (GB) __________________36.7 AVERAGE SECTORS PER TRACK ________________681 rounded down ACTUATOR TYPE ____________________________ROTARY VOICE COIL TRACKS ___________________________________105,208 CYLINDERS ________________________________26,302 user HEADS ______PHYSICAL______________________4 DISCS (3.5 in) ___________________________2 MEDIA TYPE _______________________________THIN FILM/GMR RECORDING METHOD _________________________PRML 16/17 EPR4 INTERNAL TRANSFER RATE (mbits/sec)________530 to 674 INTERNAL FORMATTED TRANSFER RATE (MB/sec)_52 to 68 EXTERNAL TRANSFER RATE (mbyte/sec) _______40 Sync Low Voltage Differential(LVD) _______80/160 Sync SPINDLE SPEED (RPM) ______________________10,028 AVERAGE LATENCY (mSEC) ___________________2.99 BUFFER ___________________________________4MB Read Look-Ahead, Adaptive, Multi-Segmented Cache INTERFACE ________________________________Ultra SCSI Wide Low Voltage Differential __________Ultra3-SCSI Wide ASA II, SCAM level 2 (1 default) BYTES PER TRACK __________________________348,900 avg SECTORS PER DRIVE ________________________71,687,369 TPI (TRACKS PER INCH) ____________________38,000
BPI (PEAK KBITS PER INCH) ________________460 AVERAGE ACCESS (ms read/write)____________5.2/6.2 Drive level without controller overhead SINGLE TRACK SEEK (ms read/write) ________0.5/0.9 MAX FULL SEEK (ms read/write) ____________10.0/11.0 MTBF (power-on hours) ____________________1,200,000 SHOCK (G's, 11/2/.5 ms): operating (Read/Write) __________15 abnormal ________________________40 nonoperating ____________________/250/150 ACOUSTICS (Bels typical) ________Idle ____3.2 Max ____ POWER DISSIPATION (watts/BTUs) Active ____/ Idle ______12.4/42.31 POWER REQUIREMENTS: +12V START-UP (amps) _2.25 +12V TYPICAL (amps) __0.70 idle +5V START-UP (amps) __1.00 +5V TYPICAL (amps) ___0.80 idle IDLE (watts) _________ Physical: Height (inches/mm): 1.00/25.4 Width (inches/mm): 4.00/101.6 Depth (inches/mm): 5.75/146.05 Weight (lbs/kg): 1.76/0.798
Click here to view the manufacturers item description/brochure |
| |
|
|
|
|